Cheap Chinese Laser

Cheap Chinese Laser

This is the page dealing with the Cheap Chinese Laser at HacDC in the upstairs room at St. Stephen and the Incarnate church in Washington, DC. This page replaces PA LaserCutter page from some years ago. It had high ideals, but poor execution.

Introduction

HacDC has a K40, 40W, CO2, water cooled, laser for CNC cutting of various materials, aka a cheap Chinese laser. It allegedly used to work just fine, but someone decided that wasn't good enough so she ordered and halfass installed some new parts that only halfass work. After our intrepid hero, James, fullyassed the installation of the new parts, the laser still only halfass worked. Tom was railroaded into helping with the software, but even so the dynamic duo couldn't get the damn thing to work. Then one day at work, boredom struck in a meeting and James had the idea to create this wiki page to guide others through the confusion and misinformation that plagues most equipment at HacDC and often results in subpar operation. I beseech you, dear reader, to continue your edification on our topic at hand and become your own evil archvillain with laser powers. (Sharks sold separately.)

Components

Chassis

The chassis is the laser itself, the blue metal box with 3 flip up lids. The main lid users deal with is for the cutting chamber on the left front of the machine. It includes an orange plastic window. The cutting chamber contains the transverse and longitudinal axes, aka x and y. X goes left to right, and y goes back to front. The material to be cut goes in this chamber. The second flip up lid is for the controls and power supplies chamber. This lid contains the front panel controls and indicators. There are two control boards, the Smoothie board and the K40 ACR plug-and-play board which connects the Smoothie board to the machine hardware. There are two power supplies as well, the control powersupply which is right below the control boards and the high-voltage (and I mean real high voltage, like around 15kV, not those nambypamby B.S. 120VAC "high voltage" warning labels) laser tube power supply which creates enough voltage to rip the electrons off the CO2 molecules and ionize them and cause them to emit coherent light when the electrons get back together with their matching CO2 ions. For more about this exciting process, read a science book. The third lid covers the laser tube chamber at the back of the chassis. You don't really need to mess with these last two lids unless you are modifying the equipment or troubleshooting a failure. All the lids have interlock switches and the laser will not fire if any one is open (unless you flip the override switch, in which case, it's your own darn fault for burning out your eye, as we say in Charlotte, "you did it to yourself").

Exhaust

The exhaust system sucks smoke from the laser chassis cutting chamber and sends it outside through a window. It was cobbled together using a fan and housing salvaged from a prior laser cutter and is mostly held together with zipties and metal duct tape. Seriously. I'm not kidding. Actual zipties and duct tape. (I'd like to give a shout-out to Home Depot for selling me the role of metal tape for only one cent.) If any part of the whole laser system is going to crap out, this would be a good part to bet on. It also uses 4" diameter (that's 105mm for those of you on the metric system) flexible metal clothes dryer exhaust duct to carry the exhaust gasses. There are custom-made, 3d-printed transiton pieces at the back of the laser chassis which replace the original feeble exhaust system. Read about them here

Cooling

The cooling system presently consists of a 5 gallon pail in the roller cabinet with a submersible pump. The water should be replaced with distilled. (The pump power cord got a new plug. It stays plugged in much better than the original cheap Chinese plug.) If the water doesn't flow, the laser will burnout. Sadness. The cooling system presently only works based on the heat capacity of the water in the bucket. Once the water heats up, you just need to wait for it to cool back down all by itself. You can read about other people with more sophisticated refrigerated cooling systems, but this was quick and easy, like a virgin on prom night. Julia has mentioned she's got some thermoelectric coolers in hiding for this project. We'll cross that bridge when we get everything else running first. The cooling system will have 3 interlocks: low water level, low flow, and high temperature.

Computer

This is CNC equipment. The first C is for Computer. (No, not for cookie, but we often have cookies anyway.) You need a computer with a USB port. You need computer software. I hope we can have a computer dedicated to the laser, but let's be real, that's not likely to happen. I hope Tom will fill out this section.

Cabinet

The cabinet is what the chassis sits on. The cabinet has wheels. It's made of particle board and painted white. The left door has upper and lower latches inside which hold it shut, so don't yank on it. The cabinet houses the cooling system, the power strip which all the line voltage equipment plugs into: exhaust fan, cooling pump, laser chassis, 12V power supply (not yet installed).

Safety Interlocks

None of these safeties are installed yet. Don't go futzing around with stuff unless you know exactly what you are doing. And tell James or Tom.

Ventilation

1. Exhaust - If the exhaust fan isn't moving air, we don't want the laser to fire and make lots of smoke which would then fill the room
2. Lens - Eventually we plan to install an air shroud nozzle around the laser lens to keep smoke from coating the lens and reducing cutting power.

Coolant

1. Level -
2. Flow
3. Temp

Doors

1. Cutting Chamber
2. Control Chamber
3. Laser Chamber - Probably not going to install this switch because the door is in back and control panel space is at a premium
4. Cabinet - Probably not going to install this switch because there's not much harm in the cabinet and control panel space is at a premium

Workflow

Prestart

1. Come up with design
2. Create SVG using software like Inkscape
3. Upload SVG to computer
4. Convert SVG to toolpath using software like Laser Draw

Startup

1. Roll cabinet out from under shelf
2. Get extension cord out of cabinet and plug laser into extension cord and extension cord into live receptacle
3. Turn on laser master power switch
4. Close cabinet door
5. Load material to be cut in laser cabinet
6. Shut lid on cutting chamber
7. Turn on laser cabinet power switch

Operations

1. Ensure all safety interlocks are operable by checking indicator lights
2. Run program without laser powered on to observe tool path and ensure material to be cut in properly arranged in the cutting chamber
3. Run program with laser powered on to cut material

Shutdown

1. Turn off laser chassis and master power switches
2. Unplug laser and extension cord
3. Coilup and store extension cord
4. Shut cabinet door
5. Roll cabinet back under the shelf
6. Continue with your evil plans for world domination

Custom Wiring

Julia had some LED strips she wanted installed. We succeeded. The illuminate when the main power is turned on.

They are white LEDs but the orange laser viewing window colors them.

Sully really likes relays and discrete, analogue circuits, so he jimmied up a bunch of stuff to make it less likely for you to poke your eye out or burn out the laser. The laser power supply from the factory takes input from 3 front panel controls: off-on laser switch, momentary-on laser switch, power control potentiometer knob. The off-on switch was a cheap latching push button which was connected to the leftmost two terminals of the 6 terminal plug with black wires. It was replaced with an off-on, metal, toggle switch on 3-23-17. The middle two terminals of the block connect to the momentary on push button switch on the front panel which causes the laser to fire (when the left two terminals are shorted together by the toggle switch). The right 3 terminals (which overlap with the right center terminal going to the push button switch) connect to the front panel potentiometer which controls the laser current. Do not turn the knob to full clockwise, because increasing the laser firing current past a certain point doesn't provide any benefit and just reduces the tube lifespan. The plan is to parallelize the push button firing switch with a solid-state relay controlled directly by the Smoothie board and bypassing the K40 ACR board (which was supposed to make the Smoothie board plug-and-play, but as mentioned earlier did a halfassed job). The potentiometer will be connected to a 3PDT switch for computerized or manual power level control. A PWM to DC circuit will do the automatic control and the original pot will remain for the manual control. The safety interlocks are basically a whole bunch of microswitches in series so if any one of them gets tripped the left two pins of the power supply 6 pin connector won't be shorted together and the laser won't fire. There's also a plan to have lights illuminate to show which safeties are operating properly or tripped. Plus indicator lights are cool. And for the remaining manual firing switches we plan on getting those flip-up red covers like in those military movies where they're firing nuclear missiles and stuff like that. These would aid in troubleshooting, and look really cool, even if they are kinda spendy. Man, this is really turning into a wall of text. Someone should do something about this sometime. Anyway, schematic drawings would go here, or links to them would go here.

Terminal Block Connections

1. Cutting chamber door safety switch - common
2. Cutting chamber door safety switch - n.o.
3. Cutting chamber door safety switch - n.c.
4. Control chamber door safety switch - common
5. Control chamber door safety switch - n.o.
6. Control chamber door safety switch - n.c.
7. Cooling water level float safety switch - common
8. Cooling water level float safety switch - n.o.
9. Cooling water level float safety switch - n.c.
19. Auto-hand power control switch - common
20. Auto-hand power control switch - n.o.
21. Auto-hand power control switch - n.c.

Custom Parts

Images of custom parts like the exhaust nozzles and eventually a new control panel and source files for 3d printed or laser cut parts can go here.

CCL front panel

Air flow switch holder

Exhaust nozzle

Terminal block holder

This image is colored for 3d printing using it as a height map: black=0mm, gray=1mm, white=2mm. 174mm wide, 184mm tall. The SVG file was created by a Ruby program to modularize the positions and sizes of cutouts for switches, nobs, lamps, etc.

Bill of Materials, a.k.a. Donation Wishlist, and Hardware Store Shopping List

1. Laser goggles
2. USB A-B cord, i.e. printer cable, which doesn't suck
3. Solid state relays -- we used [1] this one. --This should move to custom parts and off the wishlist (JS 4-20).
4. Stuff to cut
   1. 1/8" Baltic birch plywood
   2. Plastic sheets, e.g. acrylic
   3. Masonite?
5. Cabinet reinforcements
   1. dimensional lumber, e.g. 2x4, 2x2, 1x3
   2. unidirectional casters
6. Cooling system stuff
   1. Distilled water
   2. Float switch
   3. Thermocouple or thermistor/RTD temperature sensor probe
   4. Radiator and fans
   5. Solidstate heat pump
   6. Working water fountain chiller (for future use on the 100W downstairs)
   7. PLC/Microcontroller with A/D inputs for temperature probe conditioning and temp display (advanced task)
7. Green connectors for smoothieboard and laser powersupply [2]

To-Do Tasks

1. Airflow switch housing
   1. manufacture
   2. install
2. Coolant interlocks
   1. Level sensor
      1. manufacture
      2. install
   2. Flow sensor
      1. design
      2. manufacture
      3. install
   3. Temp sensor
      1. design
      2. manufacture
      3. install
3. Door switches
   1. wire up switches
4. Chassis wiring
   1. Mount one of the terminal strips and wire up the safety switches
   2. Draw a wiring diagram of custom components and label/number the terminals
5. CNC firing control - This svg file can be used to test run the laser: Laser circle test
   1. find firing signal on Smoothie board
   2. determine relay requirements
   3. purchase and receive relay
   4. install firing relay
6. CNC power control
   1. find PWM power level control signal on Smoothie board - PWM duration 300us
   2. fabricate converter - breadboarded and bench tested
   3. install converter
7. software
   1. determine best software to use
   2. develop workflows for various programs and operating systems
   3. update this page to explain the above

Completed Tasks

If you do work on the laser, please record it here.

Task	Fixer	Date	Notes
Create Wiki page	James	3/24/2017	Ongoing updates needed
Install operational exhaust system	James	2/2017	Still needs interlocks
Install cooling system	James	2/2017	Air cooling or refrigeration could be added
Connect control power supply to switched mains	James	3/2017	Done
Get x and y axis movements working	Tom	3/2017	Firing still needs to be fixed
Replaced cooling pump power cord plug	James	3/26/2017
Installed door closure bolts on left cabinet door	James	3/26/2017
Installed cutting chamber illumination LEDs and 12VDC powersupply	James	3/26/2017
Control + interlock circuits design/brainstorm session	James + Tom	3/27/2017	See webpages below for Smothieboard help
Mocked up and tested control circuit for PWM from smoothieboard	James + Tom	3/27/2017	http://smoothieware.org/laser-cutter-guide
Scoped out various pins on the smoothieboard to find PWM out	James + Tom	3/27/2017	http://smoothieware.org/smoothieboard-v1
Removed control panel	James	3/30/17	Don't mess with nothing until a new one gets installed!
Tried to 3d print a new control panel	James	4/2/17	Lulzbot Taz either didn't extrude or made bird poop. :( It's too bad we don't have a working laser cutter.
Adjusted program size parameters based on failed print and added ammeter mounting screw holes to control panel design	James	4/11/17	Still need to upload new SVG here and print it
Ordered self adhesive cable tie mounting squares and SSR for PWM-> DC	Tom	4/11/17	Delivery expected Thursday
Design 3d-printed mounting bracket/clip to hold switches for door interlocks	James + Tom	4/15/17	Impromptu Saturday night productivity session.
Design, breadboard and test PWM circuit with solid state relay and newly determined time constant	James + Tom	4/15/17	Impromptu Saturday night productivity session.
Uploaded exhaust nozzle and exhaust flow switch scad files	James	4/20/17	Flow switch needs printing and Tom's nacelle needs dimension tweeking.
Tried printing control panel on the Ultimaker2	James	4/25/17	Print failed twice, but third time looked good before I left.
Installed control panel 3d printed on Tuesday	James	4/27/17	Controls and indicators are installed but not operational, yet. It looks sweet! Could be thicker, maybe 4mm. Dimensions could use tweeking too: toggle switches moved down, corner radii reduced,...
Uploaded source code and stl for water level float switch and for terminal block holders. Installed v5 of door switch holder and soldered wires to switches.	James	5/1/17	Still need to print float switch parts and terminal block holders. New parts fit well. A very productive day overall.
Installed terminal block with manually modified v1 terminal block holder parts. Wired up cutting chamber and control chamber door safety switches. Connected laser power supply wiring to new control panel switches.	James	5/4/17	Need to adjust terminal block holder dimensions and reprint.
Uploaded v2 source code and stl for terminal block holder.	James	5/5/17	Need to print float switch parts and terminal block holders.
Printed and installed new terminal block holders (v2). Printed new air flow switch and water level float switch head and base. Remodeled exhaust header.	James	5/6/17	Holders fit great. Base, not so much.
Reprinted water level float switch base. Investigated PWM output from Smoothieboard.	Tom & James	5/7/17	Pin 4.2 and GND work for PWM signal. PWM to DC breadboard isn't working. Laser power supply 5V circuit for safety switches doesn't have enough current to illuminate the trouble lamps on front panel.
Install float switch.	James	5/11/17	Not seeming to function as of 5/14 - remains conductive even when open?
Successful CNC laser firing on circle laser test.	Tom & James	5/14/17	Some kind of beam splitting or 2-layer reflection is going on.