Prusa Mendel Documentation

A new reprap printer will built along the lines of the Prusa Mendel. You can find details of the Prusa design at the Prusa Mendel page on the reprap wiki, or you can view the sources for the Prusa at github

Intro

Having another 3d printer in the space will allow us to always have a working machine and to use one machine to help fix another if there are problems. It will also enable several people to print things out at the same time. The goal is to document this build so others can make their own printer following our documentation.

Materials for the build

BOM for Prusa Mendel

Non-Printed Parts ("vitamins")

Quantity	Description	Type	Comments
83	M8 nut	Fastener	(John)
93	M8 washer	Fastener	(John)
6	M8×30 mudguard / fender washers	Fastener	(John)
2	M4×20 bolt	Fastener	(John)
2	M4 nut	Fastener	(John)
2	M4 washer	Fastener	(John)
22	M3×10 bolt	Fastener	(John) / Space
8	M3×20 bolt	Fastener	(John) / Space
8	M3×25 bolt	Fastener	(John) / Space
4	M3×40 bolt	Fastener	(John) / Space
70	M3 washer	Fastener	(John) / Space
40	M3 nut	Fastener	(John) / Space
2	M3 grub screw / set screw	Fastener	(John) / (Pete)
3	608 roller skate / inline skate / skateboard bearing	Bearings	(Space) / Pete
4	ballpoint pen springs	Spring	Space
6	M8×370mm	Threaded rod	3 per side - (Mark) / (Space)
4	M8×294mm	Threaded rod	front / rear - (Mark) / 2 x 600 Pete / (Space)
3	M8×440mm	Threaded rod	top / bottom - (Mark) / Pete / (Space)
2	M8×210mm	Threaded rod	Z-leadscrew - (Mark) / Pete / (Space)
1	M8×50mm	Threaded rod	or bolt for X idler - (John) / (Mark) / Pete / (Space)
2	8mm×420mm	Smooth rod	X-bar - Pete / (Space)
2	8mm×406mm	Smooth rod	Y-bar - Pete / (Space)
2	8mm×350mm	Smooth rod	Z-bar - Pete / (Space)
1	225mm×225mm print top plate	Thick Sheet	(space)
1	140mm×225mm print bottom plate	Thick Sheet	space
1	840mm×5mm T5 pitch timing belt	Belt	T2.5 from Pete if it's useful
1	1380mm×5mm T5 pitch timing belt	Belt	T2.5 from Pete if it's useful
5	NEMA 17 bipolar stepper motor	Stepper	John
50	small cable binder / ziptie	Misc	(space)
1	Wade's Geared Extruder		ZAC
1	Electronics + endstops		gen3 from John or Tiny G from Alden

John

1x gen3 mobo 2x gen3 EC 5x steppers 4x stepper controllers (we'll have to pull these from the cupcake and have the cupcake use the mbi ones) 1x p4ac 4 axis stepper controller carrier board (we'll have to pull this from the cupcake too) 1x wade's extruder (assembled and working) 1x 36mm brass barrel 1x 0.5mm mbi nozzle 1x 0.5mm makergear bighead nozzle Insulator materials (have to make and document on lathe) nuts/bolts/washers - I have tons plywood/mdf for build platform

Xaq

RP parts

Still needed

threaded rods smooth rods heated build platform (if we want it, can get away with some other hacks if we want, or leave it out altogether)

Offers

Mark has threaded rod Alden has a Tiny G board... this is attractive Pete smooth rod