Actions

Category

Category:Photolithography PCB Fab

From HacDC Wiki

PCB Photoexposure Jig.jpg

When the 10mil isolation paths offered by CNC Milling are insufficient, photolithography becomes the PCB fabrication method of choice.

Large Boards

For large boards, note the following:

  • Foam backing will be needed to press the PCB evenly against a photomask. Otherwise, acrylic (and similar) frames may bubble under pressure, allowing the photomask to 'pop-up' in the middle.
  • During chemical processing, alternate between photodeveloper and etchant. Proceed with etchant only when all exposed regions are changing color. Otherwise, problems with ultrathin photoresist residue may remain.
  • Avoid placing UV light sources in extreme proximity to the board. Doing so may unevenly expose some regions.

PCB Design

Recommend gEDA. Project template with CNC Mill and gerber export scripts available on github. Photolithography scripts are specifically provided at the HacDCPhotolitho github repository.

Design Rules

Recommend at least the following tolerances:

  • 6 mil (0.15mm) feature size (traces and spacing)
  • 34 mil (0.85mm) hole size with 8 mil (0.21mm) annular ring size (50mil/1.25mm outside diameter) - fits most through-hole components, standardization on one size obviates manual milling bit swapping
  • 25 mil minimum hole size - tested for milldrilling

For comparison, oshpark offers:

The minimum specs for 2 layer orders are 6 mil traces with 6 mil spacing, and 13 mil drills with 7 mil annular rings.

Recommend most traces be kept to 10mil width, especially long traces. Note slightly better resolution is routinely feasible with practice.

Process

Simple, consisting of:

  1. Photosensitive copper clad board. If not already available, more can be made by laminating dry film photoresist to bare copper clad board.
  2. Via/hole drilling, outline milling, etc. Best done automatically on CNC mill. Please be careful to terminate outline cutting once complete, do not allow the endmill to bind.
  3. Photomask. Printed on transparencies at high-resolution. Inkjet printers, >600dpi, do well, given true inkjet transparencies. Some laser printers may require double layer photomasks. Alternatively, <445nm lasers may be able to selectively expose the photoresist.
  4. UV exposure. Sunlight or high-brightness CFL bulbs can expose the photoresist in ~5-30 minutes. EEPROM eraser boxes with timers are best. Even exposure is critical, and timing is critical for lower-contrast photomasks.
  5. Development. Use a foam brush with the appropriate developer solution from the chemicals shelf. Alternatively, a warm bath can quickly provide better consistency across large boards, particularly if photodeveloper includes silicate.
  6. Etching. Recommend a sponge with ferric chloride to remove exposed copper. This is quicker and less wasteful than the "bath" process.
  7. Carefully repeat above two steps as necessary to isolate all traces.
  8. Striping. Sodium hydroxide completely removes photoresist. May need additional UV exposure.
  9. Solder mask. Optional. Laminate two dry film photoresist sheets onto the PCB, apply photomask, expose, and develop. Alternatively, laser cut a negative solder mask from blue tape, and apply high-temperature spraypaint.

Assembly

For large boards with hundreds of components, reflow can be quicker than manual soldering.

  1. Laser cut solder paste stencil from blue tape. Apply stencil to PCB.
  2. Add smooth, paper thin layer of solder paste with a razor.
  3. Remove stencil.
  4. Place components on the appropriate pads.
  5. Carefully melt the solder with the hot-air reflow tool. Hold the hot-air tool close to the components at 400C and maximum airflow, watch carefully, and progressively move the tool across the board as solder melts.

Note that this process is somewhat incompatible with hand-soldered vias.

Resources

HacDC has the requisite resources:

  • Modified EEPROM exposure box including timer, germicidal lamp, foam backing, and laser-cut acrylic PCB/photomask holding jig.
  • Standalone polycarbonate and acrylic PCB/photomask holding jigs, for use with alternative light sources.
  • Laser printer (Phaser740, use dual layer transparency masks, monochrome only, color causes streaks).
  • Transparencies.
  • Positive photosensitive copper clad board (typically including 590-660).
  • Negative photosensitive copper clad board.
  • Negative dry film photoresist.
  • Bare copper clad board, various types and thicknesses.
  • Various photodeveloper chemicals. Use the positive developer solution and foam brush for positive resists, sodium carbonate (washing soda) for negative resists.
  • Lots of copper dissolving etchant, various types, some good, some bad.
  • CNC Mill.
  • A heated and bubbled etchant bath has been constructed by mirage335. While reasonably quick (~15 minutes) and consistent, this is not recommended, as components degrade quickly, and the resulting acid vapor is extremely harsh.

Demo

Chemically developed and etched PCB. Photoresist remaining. DevelopedEtched.jpg

Photoresist stripped, bare copper PCB electrically tested. DevelopedEtchedStrippedTested.jpg

Aligned reverse side. DevelopedEtchedStrippedTested Reverse.jpg

Reference

http://www.instructables.com/id/Killer-PCBs/ http://www.mgchemicals.com/downloads/pdf/negativePrototyping.pdf http://www.instructables.com/id/Sponge-Ferric-Chloride-Method-Etch-Circuit-Bo/

Credit

Many thanks to:

  • Dan Barlow

Research Underway

  • Better photodeveloper. The MG Chemicals product works reasonably well thus far, but may not include sodium silicate. [Reportedly] RS-Components 690-849 is far superior, allowing development in seconds with lower risks of overdevelopment.
  • Alternative photoresist, as reported at [1].
  • DLP projector maskless lithography.
  • Tracing paper photomasks, as reported at [2].
  • Professionally printed or phototypeset photomask (perhaps kinkos does this).
  • PCB processing spray tanks for developing and etching. Expected to improve quality and ease of use, allowing higher yields and more attempts as necessary.
  • CircuitWriter repair pen to repair scratched or undercut traces.
  • Conductive ink, rivet (http://www.megauk.com/through_hole_rivets.php), or 'bar' (http://www.technick.net/public/code/cp_dpage.php?aiocp_dp=guide_pcb) through-hole connections. Apparently, the rivets can be used without the expensive punch tool (http://www.electricstuff.co.uk/pcbs.html).

Full-Scale Process

Professional PCB fabs manufacture upwards of dozens of PCBs per hour, with resulting boards ready for rapid solderpaste stencil based PCB assembly. Efforts are underway to implement required DLP projection and spray tank equipment for at least part of this process, a description of which follows:

Dual-Layer Boards

  1. Positive presensitzed board, negative artwork (dark regions cover desired copper).
  2. Predrilling if dual pre-aligned DLP projection is not available.
  3. UV photoexposure, high contrast, using DLP projection.
  1. Warm photodevelopment bath (exposes desired copper).
  2. Rinse spray (pH should be neutral -<1.5).
  3. Via/hole drilling, if not done already.
  4. Conductive ink coating, to activate through-holes (http://www.thinktink.com/stack/volumes/volvi/condink.htm).
  5. Recirculated electroplating bath (adds copper everywhere, including holes). Requires specialized copper plating solution (http://www.thinktink.com/stack/volumes/voliii/consumbl/cplatmix.htm) .
  6. Liquid tin plating (simple bath, no spraying) covers everything with tin, which resists etchant.
  7. Photoresist stripping with concentrated sodium hydroxide.
  8. Etching spray removes bare copper, leaves previously tinplated surfaces unharmed.
  9. Rinse spray (pH should be neutral -<1.5).
  10. Tin stripping spray (http://www.alliedelec.com/search/productdetail.aspx?SKU=70125740) leaves bare copper.


Multilayer Boards

Photo-Patterning (All Layers)

  1. Positive presensitzed board, negative artwork (dark regions cover desired copper), single-sided for exterior layers, double-sided for interior layers.
  2. Predrill registration holes in panel corners.
  3. Predrill all holes if dual pre-aligned DLP projection is not available.
  1. UV photoexposure, high contrast, using DLP projection.
  2. Warm photodevelopment bath (exposes desired copper).
  3. Rinse spray (pH should be neutral -<1.5).

All layers should now have correctly developed/patterned photoresist on bare thin copper.

Interior Processing

  1. Recirculated electroplating bath (adds copper everywhere, except holes). Requires specialized copper plating solution (http://www.thinktink.com/stack/volumes/voliii/consumbl/cplatmix.htm) .
  2. Liquid tin plating (simple bath, no spraying) covers everything with tin, which resists etchant.
  3. Photoresist stripping with concentrated sodium hydroxide.
  4. Etching' spray removes bare copper, leaves previously tinplated surfaces unharmed.
  5. Tin stripping spray (http://www.alliedelec.com/search/productdetail.aspx?SKU=70125740) leaves bare copper.

Interior layers should now be fully processed, down to thick patterned copper.

Bonding

  1. Rinse spray (pH should be neutral -<1.5).
  2. Bond stack with heated press and adhesive (ideally pre-preg).

Completed interior layers are now buried, with exterior layers still holding developed/patterned photoresist on bare thin copper.

  • Full Stack
  1. Via/hole drilling, if not done already.
  2. Conductive ink coating, to activate through-holes (http://www.thinktink.com/stack/volumes/volvi/condink.htm).
  3. Recirculated electroplating bath (adds copper everywhere, especially holes). Requires specialized copper plating solution (http://www.thinktink.com/stack/volumes/voliii/consumbl/cplatmix.htm) .
  4. Liquid tin plating (simple bath, no spraying) covers everything with tin, which resists etchant.
  5. Etching' spray removes bare copper, leaves previously tinplated surfaces unharmed.
  6. Tin stripping spray (http://www.alliedelec.com/search/productdetail.aspx?SKU=70125740) leaves bare copper.

Exterior layers should now be fully processed, down to thick patterned copper. Through-holes should now be plated by the same extra copper added to exterior layers. Interior layers are completed, with via copper edges adjoining the through-hole plating. Tin plating should have protected the through-holes and associated copper joints.

At this point, the multilayer board should be physically and electrically flawless.

Expensive Components

  • 3 * $90 - SHURflo Industrial Pump Model #2088-594-154 114V Corrosion Resistant Pumps (Electroplating, etching, tin stripping spray tanks). Don't bother looking for another pump, this one has actually been used in an etchant sprayer system, and can be expected to survive the extremely harsh chemicals.
  • 4 * $15 - Specialized Heater (Photodevelopment bath, electroplating, etching, tin stripping spray tanks).
  • 36 * $2 - Toro 3GPH Mister
  • 2 * ~$150 DLP Projector

Minimum cost to implement the full system is therefore around $700, a $1k budget is probably reasonable. Better projectors may be worth investing in, to ensure highly successful fabrication results are achieved.

Environmental Concerns

Cupric Chloride (typically the green stuff) should be used as the etchant, as it can be recharged completely with atmospheric oxygen and hydrochloric acid.

Subcategories

This category has only the following subcategory.