Actions

Lulzbot TAZ 1.0: Difference between revisions

From HacDC Wiki

(Add link to OHAI calibration instructions)
(Added dynamic symlink info and full pronsole output)
Line 9: Line 9:
<pre>$ pronsole
<pre>$ pronsole
offline&gt; connect /dev/ttyACM2 115200
offline&gt; connect /dev/ttyACM2 115200
ttyACM2 21°&gt;
ttyACM2 21&deg;&gt;
</pre>
</pre>


Line 19: Line 19:


Because we neither have the original paperwork for the TAZ, nor were the EEPROM settings previously enabled, we may be forced to determine the ESTEPS settings via, IMHO, a method fraught with inacuracy by trying to [https://ohai.lulzbot.com/project/extruder_calibration/calibration/ manually calibrate using the OHAI instructions].
Because we neither have the original paperwork for the TAZ, nor were the EEPROM settings previously enabled, we may be forced to determine the ESTEPS settings via, IMHO, a method fraught with inacuracy by trying to [https://ohai.lulzbot.com/project/extruder_calibration/calibration/ manually calibrate using the OHAI instructions].
== Adding a dynamic symlink to the TAZ... ==
After massaging the OS with the procedures listed in [[Dynamic symlinks for 3D printers]] we see:
<pre>$ pronsole
WARNING:root:Could not setup DBus for sleep inhibition: org.freedesktop.DBus.Error.NotSupported: Unable to autolaunch a dbus-daemon without a $DISPLAY for X11
Welcome to the printer console! Type "help" for a list of available commands.
offline&gt;
offline&gt; connect /dev/TAZ 115200
start         
Printer is now online
External Reset
Marlin 1.0.0 
Last Updated: 2013-03-06 | Author: LulzBot
Compiled: Apr 17 2015
Free Memory: 5504  PlannerBufferBytes: 1232
TAZ PC&gt;
TAZ 21&deg;&gt;
</pre>
Note the details on the firmware. Namely:
* Marlin 1.0.0 
* Last Updated: 2013-03-06 | Author: LulzBot
* Compiled: Apr 17 2015

Revision as of 00:53, 22 January 2019

2019.01.17

The "newest" addition to our collection of 3D printers is actually the oldest: The Lulzbot TAZ is actually, a Lulzbot TAZ 1.0 (according to the serial number on the back: KT-PR0010-5147).

The index.html at http://devel.lulzbot.com/TAZ/ says, among other things: *"B" - KT-PR0010 - TAZ 1.0

Using minicom, the speed was determined to be 115200. Sending G28 to home it made it grind gears.

$ pronsole
offline> connect /dev/ttyACM2 115200
ttyACM2 21°>

Eventually, I found http://download.lulzbot.com/TAZ/1.0/hardware/electronics/RAMBo/ which identifies the board as "based off of the Arduino MEGA" with "5 stepper drivers" and "5 MOSFET switched outputs" with documentation at http://reprap.org/wiki/rambo

As near as I can tell, the latest in firmware and other software lives at http://download.lulzbot.com/TAZ/1.0/software/current/firmware/Marlin/

Lulzbot offers instructions on re-flashing your 3D printer's firmware and see also RepRap's RAMBo firmware page.

Because we neither have the original paperwork for the TAZ, nor were the EEPROM settings previously enabled, we may be forced to determine the ESTEPS settings via, IMHO, a method fraught with inacuracy by trying to manually calibrate using the OHAI instructions.

Adding a dynamic symlink to the TAZ...

After massaging the OS with the procedures listed in Dynamic symlinks for 3D printers we see:

$ pronsole
WARNING:root:Could not setup DBus for sleep inhibition: org.freedesktop.DBus.Error.NotSupported: Unable to autolaunch a dbus-daemon without a $DISPLAY for X11
Welcome to the printer console! Type "help" for a list of available commands.

offline>
offline> connect /dev/TAZ 115200
start          
Printer is now online
External Reset 
Marlin 1.0.0   
Last Updated: 2013-03-06 | Author: LulzBot
Compiled: Apr 17 2015
Free Memory: 5504  PlannerBufferBytes: 1232
TAZ PC>
TAZ 21°>

Note the details on the firmware. Namely:

  • Marlin 1.0.0
  • Last Updated: 2013-03-06 | Author: LulzBot
  • Compiled: Apr 17 2015