Actions

Hacdc log: Difference between revisions

From HacDC Wiki

(Oct. 19)
(update)
Line 43: Line 43:
The Taz jammed & Julia cleared a clog from the printhead. The Algix filament did not print satisfactorily. A print with leftover filament worked but a new roll of filament had problems with stripping. A member swapped a nonworking (regular) Kodak printer for a working (after a little work) Epson one. A visitor tried to use the CNC mill (note that the parallel cable connects to the upper connector on the computer) but the y axis would not move.
The Taz jammed & Julia cleared a clog from the printhead. The Algix filament did not print satisfactorily. A print with leftover filament worked but a new roll of filament had problems with stripping. A member swapped a nonworking (regular) Kodak printer for a working (after a little work) Epson one. A visitor tried to use the CNC mill (note that the parallel cable connects to the upper connector on the computer) but the y axis would not move.
Oct. 19
Oct. 19
The filament on the Taz may require a higher temperature; testcube printed fine at 225 C. The boxes have been recompiled for the Rostock (box1t32Rf.gcode etc. in /ImplicitCAD/Radioshack_box on renderadmin) and the zero-thickness problem eliminated.
The filament on the Taz may require a higher temperature; testcube printed fine at 225 C. The boxes have been recompiled for the Rostock (box1t32Rf.gcode etc. in /ImplicitCAD/Radioshack_box on renderadmin) and the zero-thickness problem eliminated. Tried to print a box3 at 225 but the filament started feeding erratically and the printhead now seems completely jammed like before.
</nowiki>
</nowiki>

Revision as of 03:46, 20 October 2018

I thought it would be good to keep a log of what's going on. Contributions encouraged. Aug. 14, 2018 The box2 print on the Taz had finished but was about a mm short, presumably due to a likely z axis skipping problem. I later stopped someone else's print because filament had stopped extruding, then noticed that the new filament guide tube was missing & the reel, which had been changed (light green), was on backwards. I fixed the reel and the print worked (but looked sloppy). I found the missing tube on the previous reel (white), reinstalled it, and, after adjusting the printhead height, started another box2. I also redesigned the probe mount for the Taz (probemount2A.escad & probemount2B.escad (both at renderadmin/ImplicitCAD/radioshack_box)). Neither regular printer was working. Aug. 16 The box2 print failed due to the same intermittent connection failure that's been plaguing the printer. Had delayed monthly meeting. Julia worked extensively to fix the z axis skipping but the z axis now keeps getting badly out of level between the 2 sides so the Taz is unusable. On the other hand, after turning on the controller (it was off but I think it was on on Aug. 14), both regular printers are now working. Aug. 20 Julia located a good design for a replacement extruder for the Ultimaker. Julia worked on the Taz. It it now working but the z axis still seems to be skipping & the intermittent disconnect problem is probably still there. There is now a box for RODS. Caution: It is dangerously topheavy. Aug. 23 A box again printed successfully but was a mm short. Julia rebuilt the Taz. Started another box but the filament stopped feeding; shut printer off. I added documentation to the Wiki on the laser cutter but unfortunately broke the front panel (flimsy plastic); I was able to sort of fix it by adding washers. Sept. 1 Rewired laser cutter (details in Cheap Chinese Laser entry). The laser should now be ready for testing by an expert. Several people from Nova Labs visited. They said Nova Labs would probably help HacDC fix broken equipment (if we can get it there). Sept. 3 Tom showed up to test the laser cutter. Manual firing worked but safeties did not. Got computer control of mirrors working but computer did not fire laser. See Cheap Chinese Laser entry for details. Due to the Wiki being uneditable the log was not updated. To summarize some of what happened: Julia replaced the power supply for the 3D printer computer monitor which may have been causing the random printer disconnections. She found that one roll of filament was causing problems because it needed to be extruded at 230 C (no simple way to test this). She also added heat sinks on the Taz z axis controller & stepper motors which solved the skipping problem. The Wiki was cleaned up (causing the above-mentioned uneditability). A test piece (the "sphinx") for the new Ultimaker extruder was printed. Oct. 4 The basement was found open & the lock for the outer grate is missing; it was temporarily replaced with a combination lock (contact Julia if you need the combination). Oct. 5 There was considerable chaos with Nick & people looking for him showing up at different times (finally resolved). The phone doesn't work. New parts for the Taz z axis are here. The science event list was finally updated (about time). Started printing a box4. Oct. 8 Phone is working. box4 & an Arduino cover printed well; started a box3. Finished design (still need to set values) for z-x rod joint for improved Taz z axis drive & the sphinx. Oct. 9 box3 printed well, started another. Only 4 people (including a new member) at the monthly meeting; little to report. Finished design for general pulley mount. Oct. 11 box3 failed due to filament stripping. Successfully printed stenograph machine stand. Started printing test body for new Ultimaker extruder. Fixed Cura so it will work for Rostock; tabletop computers D8PGDD1, 1M0QJH1, 5VVYKH1, & DJ7VKC1 now work. Determined that problem with some faulty tabletop computers was the USB drive and rewrote one drive. Created new HacDC hacks entry on Blabber to document fixes like how to change the cordless phone ring & fix Cura. Oct. 15 Extruder body print failed due to filament stripping but several other prints worked. The Algix filament was found to print well at an unusually low 180 C. Julia worked on the Rostock. Oct. 18 The Taz jammed & Julia cleared a clog from the printhead. The Algix filament did not print satisfactorily. A print with leftover filament worked but a new roll of filament had problems with stripping. A member swapped a nonworking (regular) Kodak printer for a working (after a little work) Epson one. A visitor tried to use the CNC mill (note that the parallel cable connects to the upper connector on the computer) but the y axis would not move. Oct. 19 The filament on the Taz may require a higher temperature; testcube printed fine at 225 C. The boxes have been recompiled for the Rostock (box1t32Rf.gcode etc. in /ImplicitCAD/Radioshack_box on renderadmin) and the zero-thickness problem eliminated. Tried to print a box3 at 225 but the filament started feeding erratically and the printhead now seems completely jammed like before.