Klipper: Difference between revisions
From HacDC Wiki
Ubuntourist (talk | contribs) (updating) |
Ubuntourist (talk | contribs) (updating) |
||
| Line 3: | Line 3: | ||
Hack-a-day offered a project [https://hackaday.com/2017/12/26/fast-3d-printing-with-raspberry-pi-but-not-how-you-think/, Fast 3D Printing with Raspberry Pi — But Not How You Think]. However, it describes how to do stuff via OctoPi (child of OctoPrint), which we don't want to use. This led to the question [https://github.com/KevinOConnor/klipper/issues/138 "Any way to divorce Klipper from Octo*?"] and also [https://www.freelists.org/post/klipper/Klipper-as-daemon,1 "Klipper as daemon"] | Hack-a-day offered a project [https://hackaday.com/2017/12/26/fast-3d-printing-with-raspberry-pi-but-not-how-you-think/, Fast 3D Printing with Raspberry Pi — But Not How You Think]. However, it describes how to do stuff via OctoPi (child of OctoPrint), which we don't want to use. This led to the question [https://github.com/KevinOConnor/klipper/issues/138 "Any way to divorce Klipper from Octo*?"] and also [https://www.freelists.org/post/klipper/Klipper-as-daemon,1 "Klipper as daemon"] | ||
Most of our machines use the [https://en.wikipedia.org/wiki/Atmel_AVR Atmega AVR] [http://www.microchip.com/wwwproducts/en/atmega2560 2560] Rambo board. But we'll start with the Aden rebuild which uses the [https://en.wikipedia.org/wiki/Atmel_AVR Atmega AVR] [http://www.microchip.com/wwwproducts/en/atmega644p 644p]. Both are 16 MHz. | |||
== [https://github.com/KevinOConnor/klipper/blob/master/docs/Installation.md Installation] == | |||
Most of our machines use the [https://en.wikipedia.org/wiki/Atmel_AVR Atmega AVR] [http://www.microchip.com/wwwproducts/en/atmega2560 2560] Rambo board. But we'll start with the Aden rebuild which uses the [https://en.wikipedia.org/wiki/Atmel_AVR Atmega AVR] [http://www.microchip.com/wwwproducts/en/atmega644p 644p]. Both are 16 MHz. So, select the proper microprocessor and speed in the '''menuconfig''' step below. | |||
$ make menuconfig | $ make menuconfig | ||
Revision as of 01:11, 30 January 2018
2018.01.25
Hack-a-day offered a project Fast 3D Printing with Raspberry Pi — But Not How You Think. However, it describes how to do stuff via OctoPi (child of OctoPrint), which we don't want to use. This led to the question "Any way to divorce Klipper from Octo*?" and also "Klipper as daemon"
Installation
Most of our machines use the Atmega AVR 2560 Rambo board. But we'll start with the Aden rebuild which uses the Atmega AVR 644p. Both are 16 MHz. So, select the proper microprocessor and speed in the menuconfig step below.
$ make menuconfig
$ make
Build Kconfig config file
Creating symbolic link out/board
Compiling out/src/sched.o
Compiling out/src/command.o
Compiling out/src/basecmd.o
Compiling out/src/debugcmds.o
Compiling out/src/gpiocmds.o
Compiling out/src/stepper.o
Compiling out/src/endstop.o
Compiling out/src/adccmds.o
Compiling out/src/spicmds.o
Compiling out/src/pwmcmds.o
Compiling out/src/avr/main.o
Compiling out/src/avr/timer.o
Compiling out/src/avr/gpio.o
Compiling out/src/avr/watchdog.o
Compiling out/src/avr/serial.o
Building out/compile_time_request.o
Version: v0.5.0-108-g1b3ef8a-20180125_195156-hostname
Linking out/klipper.elf
Creating hex file out/klipper.elf.hex