Reprap

The reprap can be found in the workshop room, on a rolly-cart. It is driven by a computer (also on the cart) named norbert (as in the angry beavers... beavers make stuff, its logical...). To use the reprap, ssh or VNC into norbert (ask Tommy for the passwd), and run skeinforge and company from there.

Our reprap is unfortunately a bit of a mongrel. Its extruder is half-way between two normal versions, and I've made several small fixes trying to make it more reliable.

Log into norbert:

norbert is the computer under the reprap. It runs FreeBSD, and lurks on that little wired network on the cart at 192.168.0.47. Plan A is to simply connect to the VNC server at 192.168.0.47:1. Ask Tommy for the passwd. Plan B, if someone has killed norbert, is to ssh in, start the VNC server, and then proceed to plan A.

To render an STL file to gcode:

Get your stl file onto norbert with scp or something, then type the command:

skeinforge foo.stl

(only use the correct filename, instead of foo.stl... It'll take a while.)

That will probably generate a file named foo_export.gcode. You then need to run that gcode file through the correctz script. (It will rewrite Z translations so they are only along the Z axis, and run them in G0. This is a workaround for a bug in the firmware.)

correctz foo_export.gcode > foo.gcode

I do not recommend bringing in pre-rendered gcode, skeinforge has approximately 3 billion parameters, and I have tweaked a few of them.

The Incantation of Calibration

This procedure has been tested... but /only/ this procedure. If you try to do things out of order, all bets are off. That may involve restarting from the beginning.

Replace any mangled blue tape

The platen is covered with blue tape, to improve the plastic's ability to stick to it. Replace any excessively mangled parts. Make sure you use the right flavor of tape, there is a slightly darker much slicker blue tape which does not work.

Turn it on

Shove the extruder into the corner of the platen labeled "origin C1"

Plug the AC powerline into the box under the ardoweenie

Run reprap.kerm

Press reset on the ardoweenie.

Wait for it to say "Found it!"

There is a bit of a race condition, you may need to hit reset again. The script will keep saying "poke?" until it finds it.

You should now have a prompt which looks like >. Enter "?" for help. If you use the g command to send straight gcode, type control-right-square-bracket and then c to get back to the > prompt.

Adjust the platen, so its co-planer with the extruder

Type "c2"

Did it make horrible noises? Stop now.

Take the gauge block (it looks suspiciously like a heat sink) and put it between the platen and the flange on the extruder (the flange does get hot). Adjust the height of the extruder (by typing u and d, to move it Up and Down, and twisting the timing belt pulley on the Z axis for fine adjustments) so the gauge block is just touching the flange. Up and Down are defined relative to the extruder. Up increases the height of the extruder above the platen.

Type "c3"

Did it make horrible noises? Stop now.

Take the gauge block, and put it under the flange again. BUT this time adjust the height of the platen instead of the extruder, using the nut on the end of the threaded rod which is right beside the C3 label.

Type "c4" (detect a pattern here?)

If you've made it this far, it shouldn't make any horrible noises. But if it does, Stop.

Repeat like at c3, only use the nut between C1 and C4. Note that there are three nuts, not four. Only takes three points to define a plane.

Type "c1"

 Now you're back at the start.

Double-check the height of the extruder with the gauge block, but it should be OK.

Repeat as necessary.

Load the Gcode, and fine-adjust the Z

type "c"

Now you're in the center (and at Z coord 7).

type "f" and give it your gcode filename at the prompt.

This MUST be done at c.

The extruder MUST also be warmed up.

type "z"

The extruder will drop down to Z=0, and extrude a square. (the square is the bounding box of the obeject, so now you know where it'll be printing it). Tweek the Z axis by twisting the pulley, until the plastic is mushed down onto the platen "right".

Scrape off the plastic, and repeat until you're satisfied.

And the monkey presses the button

Cross your fingers and type "t"

If the gcode just isn't working out, hit ^c a few times. Commands are buffered, so it won't stop immediately.

If there are mechanical issues, unplug the power cord.

And don't forget to unroll more reprap-chow as it goes. It must be unrolled, not pulled off the side, or it will miss-feed.

Eventually it'll finish, pull the extruder out of the way and turn it off. Exit from the reprap.kerm script with control-c. If you wish to make another object, you will need to start over with reseting the ardoweenie.

Maintenance

The X axis is the "inner most" one. The Y axis then moves the X axis back and forth. The Z axis should be obvious... The reprap tends to shed parts as it runs. Don't leave it unattended.

Our extruder has led a rough life. You've probably noticed that its not vertical. Don't try to bend it back. Less obviously, its temperature sensor is broken. So right now, it has no thermostatic control. Repair is basically impossible, the trauma of getting to the point that the temp sensor could be replaced is so destructive that its not worth it. The newer extruder designs work much better anyway. The only problem is that it will involve getting the RS-485 stuff working.

To recompile the firmware

cd /usr/home/norbert/reprap/arduino-0017 ./arduino

load the file /usr/home/norbert/reprap/subversion/reprap/trunk/reprap/firmware/FiveD_GCode/FiveD_GCode_Interpreter/FiveD_GCode_Interpreter.pde There is no good way to just type filenames...  :-P

Make sure Tools->Board->Sanguino is selected.

Struggle through the horrible editor...

Push the upload button. The compile might succeed, but the upload will fail, don't worry about it. Instead run the flashit script:

cd /usr/home/norbert/reprap/subversion/reprap/trunk/reprap/firmware/FiveD_GCode/FiveD_GCode_Interpreter ./flashit

Just before you press return (running the flashit script) hit the reset button on the ardoweenie. It will complain about the expected signature being wrong it does that because I incorrectly flashed it a very long time ago, and have been unable to correct/getaroundtocorrecting the signature.

Retry until it succeeds...

If the extruder doesn't extrude

First, is it warmed up? Make sure it is before trying to run it.

If you missed that part:

The extruder pinches the reprap-chow between a gear and a pinch wheel. If the motor is run before the extruder is warmed up, the gear will "strip" the plastic, and cease to go forward. To address that problem, make sure the extruder is warmed up, and then twist the reprap-chow where its going into the extruder, so the gear gets to chew on an undamaged area. It will then start moving again, and you can let go of the plastic.