Actions

Category

Photolithography PCB Fab: Difference between revisions

From HacDC Wiki

No edit summary
No edit summary
Line 4: Line 4:
The process is simple, consisting of:
The process is simple, consisting of:
1) Dry film photoresist, laminated onto copper clad board by laminator.
1) Dry film photoresist, laminated onto copper clad board by laminator.
2) UV exposure. Can be done by UV laser strapped to CNC mill or high-resolution inkjet printed transparencies and various random light sources (eg. sunlight, CFLs, etc).
2) UV exposure. Can be done by low-power UV laser strapped to CNC mill or high-resolution inkjet printed transparencies and various random light sources (eg. sunlight, CFLs, etc).
3) Development. Strong basic solution (sodium carbonate seems preferred) chemically removes exposed resist.
3) Development. Strong basic solution (sodium carbonate for negative resists, sodium hydroxide + sodium silicate for positive resists) chemically removes exposed resist.
4) Etching. Acid solution removes exposed copper.
4) Etching. Acid solution removes exposed copper.
5) Striping. Sodium hydroxide completely removes photoresist residue. Probably unnecessary and/or excessive.
5) Striping. Sodium hydroxide completely removes photoresist residue. Probably unnecessary and/or excessive.
Line 13: Line 13:
For surface mount projects, solder paste stencils are the easiest assembly technique, and can be made from blue tape on HacDC's laser cutter.
For surface mount projects, solder paste stencils are the easiest assembly technique, and can be made from blue tape on HacDC's laser cutter.


HacDC has all the required materials except the dry film photoresist.
HacDC has all the required materials. The chemical process has been thoroughly tested, and a multilayer photomask has produced slightly better than 10 mil resolution. A more capable photomask printer is strongly expected to enable 'professional' 6 mil or better resolution.


=Reference=
=Reference=
http://www.instructables.com/id/Killer-PCBs/
http://www.instructables.com/id/Killer-PCBs/
http://www.mgchemicals.com/downloads/pdf/negativePrototyping.pdf
http://www.mgchemicals.com/downloads/pdf/negativePrototyping.pdf

Revision as of 04:31, 13 January 2014

When the 10mil isolation paths offered by CNC Milling are insufficient, photolithography becomes the PCB fabrication method of choice.

The process is simple, consisting of: 1) Dry film photoresist, laminated onto copper clad board by laminator. 2) UV exposure. Can be done by low-power UV laser strapped to CNC mill or high-resolution inkjet printed transparencies and various random light sources (eg. sunlight, CFLs, etc). 3) Development. Strong basic solution (sodium carbonate for negative resists, sodium hydroxide + sodium silicate for positive resists) chemically removes exposed resist. 4) Etching. Acid solution removes exposed copper. 5) Striping. Sodium hydroxide completely removes photoresist residue. Probably unnecessary and/or excessive. 6) Solder mask. Optional. Repeat steps 1-3 and bake in oven at 220F for 10 minutes. Alternatively, laser cut a negative solder mask from blue tape, and apply high-temperature spraypaint. 7) Via/hole drilling, punching, etc. Easy to do with the thin variety of copper clad board. Alternatively, can be done automatically on CNC mill. If using printed transparency photomask, CNC milling should be done first to ease alignment.

For surface mount projects, solder paste stencils are the easiest assembly technique, and can be made from blue tape on HacDC's laser cutter.

HacDC has all the required materials. The chemical process has been thoroughly tested, and a multilayer photomask has produced slightly better than 10 mil resolution. A more capable photomask printer is strongly expected to enable 'professional' 6 mil or better resolution.

Reference

http://www.instructables.com/id/Killer-PCBs/ http://www.mgchemicals.com/downloads/pdf/negativePrototyping.pdf

Subcategories

This category has only the following subcategory.