Latest revision as of 18:18, 19 July 2016

Just as electronic breadboards often rely on integrated circuits (notably OpAmps), external power, and test equipment, optical tables also benefit from more than simple packaged lenses. Here we document the optical tools available at HacDC, many of which are self-made.

Source files are kept at https://github.com/HacDC/HacDCOptics .

Tools

Complex drop-in optical systems, ready to create or analyze complex light fields.

WideBeam

A wide beam of high-intensity collimated light is useful for manually checking the results of complicated optical beampaths. Work in progress for 2" and 8" optical axis modules.

DLPMod

HacDC has access to some DLP projectors, absent working light sources. These can be used as re-configurable image sources and high-speed light gates.

Lasers

Variety of 2" optical axis laser mounting hardware in progress.

Fixtures

Generic mounting hardware.

Tilt and Roll Platform

Even if we could afford them, commercial systems are too expensive to permanently dedicate to completed projects (~$500). Instead, we will 3D print or laser-cut a screw-adjusted spring-loaded platform, much the same as the adjustable bed used by many 3D printers.

Elements

Spatial Filter

Work in progress for 2" optical axis modules, with varying diameter pinholes.

Standards

External

Standards set for us by manufacturers.

Tapped holes, ¼-20" UNC on a 1" (25.4 mm) grid. May be roughly compatible with some M6 on 25mm grid for optical systems with non-critical dimensions.
Standard optical axis heights include 330mm/13", and possibly 1.15", 1.75", 2", 3.38", 4.5", 6.25", 8" http://www.edmundoptics.co.uk/optomechanics/optical-mounts-plates/lens-mounts/optical-cell-kinematic-mounts/2592.
Cage square lengths include at least 16mm, 30mm, 60mm.

Internal

Standards we have elected to follow from the above, or have established ourselves, as we build our own tooling.

mirage335

These standards are chosen to permit quick transition between optical table, rail, and cage systems, with only small height-adding brackets.

Stage

Stages directly connecting to extrusions are named "Series20/40/60" depending on the minimum width in millimeters. For instance Series40 mounts require two screws, 20mm apart, and have a maximum width of 40mm, all suitable for mounting on typical 20x40mm extrusions.

Substages mounted to an earlier kinematic stage or bare baseplate must fit around the rectangular opening for that series.

By default, these standards conform to the "Small" standard under "Optical Table Axis Heights".

Series	Axis Height	Opening	MaxThickness	Notes
TinySeries20	15mm	14x14mm	6mm	Specialized non-standard axis height.
Series20	35mm	14x14mm	6mm	Specialized non-standard axis height.
Series40	30.8mm	18x28mm	6mm
Series60	30.8mm	28x38mm	2mm

Mounting Holes

Tolerances intended for well-calibrated 3D printers.

Table

Screw diameter - 6mm (M6) to 6.35mm (¼in UNC) .
Hole spacing - 25mm (metric) to 25.4mm (1in imperial) .

Hole size - 8mm .
Hole spacing - 25.2 mm .

Extrusion

Screw diameter - 5mm (M5) .
Hole spacing - 20mm .

Hole size - 5.5mm .
Hole spacing - 20.25mm .

Optical Table Axis Heights

Standard axis heights are based upon typical hardware for 1" grid optical tables. Mounts for other arrangements, such as a 20series extrusions, should use corespondingly lower heights. Options to mount such hardware to a standard table through intermediate stages, such as 20series extrusions themselves, should be preserved.

Small axis height is typical, and should be assumed unless noted otherwise.

Element Size	TableHeight	ExtrusionHeight	Comments
Small	2in/50.8mm	30.8mm	Intended for lenses up to 1" high, including salvaged projector, disposable camera, and microscope components.
Large	8in/203.2mm	183.2mm	Accommodates larger lenses, particularly for light gathering and projection systems.
ExtraLarge	13in/330.2mm	310.2mm	Accommodates modest Fresnel lenses.

Optical Cage Square Lengths

Element Size	Height
Small	30mm/1.1811"
Medium	60mm/2.3622"
Large	6.25"

Reference

Printed Breadboard - http://www.thingiverse.com/thing:9040
Aluminum Angle Mounts - http://www.thingiverse.com/thing:38062
Lens Mount - http://www.thingiverse.com/thing:26752/#files http://www.thingiverse.com/thing:62693/#files
OpenSource Optics - http://www.appropedia.org/Open_source_optics
Linear Translator - http://www.thingiverse.com/thing:144838
Metal Lens Mounts - http://www.edmundoptics.com/optomechanics/optical-mounts-plates/lens-mounts/
Lasercut Optics Bench - https://hackaday.io/project/10707-lasercut-optics-bench

@@ Line 1: / Line 1: @@
 [[Category:OpticalTable]]
+[[File:Tiny20Series Photo.jpg|400px|thump|right]]
+[[File:Series20Tiny-ThreeAxis.png|400px|thumb|right]]
+[[File:Render.png|400px|thumb|right]]
 Just as electronic breadboards often rely on integrated circuits (notably OpAmps), external power, and test equipment, optical tables also benefit from more than simple packaged lenses. Here we document the optical tools available at HacDC, many of which are self-made.
@@ Line 26: / Line 29: @@
 ==Spatial Filter==
 Work in progress for 2" optical axis modules, with varying diameter pinholes.
-=Adapters=
-Mounts made to mount optical rails and cages to the table.
 =Standards=
 ==External==
 Standards set for us by manufacturers.
-* Tapped holes, ¼-20" UNC on a 1" (25.4 mm) grid. May be compatible with M6 on a 25 mm grid for optical systems with non-critical dimensions. (TODO: Verify our table is imperial, not metric.)
+* Tapped holes, ¼-20" UNC on a 1" (25.4 mm) grid. May be roughly compatible with some M6 on 25mm grid for optical systems with non-critical dimensions.
 * Standard optical axis heights include [http://www.optikos.com/products/lens-platforms-mounts/ 330mm/13"], and possibly [http://www.thorlabs.com/NewGroupPage9_PF.cfm?Guide=10&Category_ID=16&ObjectGroup_ID=60 1.15", 1.75"], [http://www.edmundoptics.co.uk/optomechanics/optical-mounts-plates/lens-mounts/optical-cell-kinematic-mounts/2592 2", 3.38", 4.5", 6.25", 8" http://www.edmundoptics.co.uk/optomechanics/optical-mounts-plates/lens-mounts/optical-cell-kinematic-mounts/2592].
 * Cage square lengths include at least [http://www.thorlabs.com/navigation.cfm?guide_id=2002 16mm, 30mm, 60mm].
 ==Internal==
 Standards we have elected to follow from the above, or have established ourselves, as we build our own tooling.
@@ Line 41: / Line 42: @@
 These standards are chosen to permit quick transition between optical table, rail, and cage systems, with only small height-adding brackets.
-====Optical Table Axis Heights====
+====Stage====
+Stages directly connecting to extrusions are named "Series20/40/60" depending on the minimum width in millimeters. For instance Series40 mounts require two screws, 20mm apart, and have a maximum width of 40mm, all suitable for mounting on typical 20x40mm extrusions.
+Substages mounted to an earlier kinematic stage or bare baseplate must fit around the rectangular opening for that series.
+By default, these standards conform to the "Small" standard under "Optical Table Axis Heights".
 {| border="1" style="border-collapse:collapse"
-!Element Size
+!Series
-!Height
+!Axis Height
-!Comments
+!Opening
+!MaxThickness
+!Notes
+|-
+|TinySeries20||15mm||14x14mm||6mm||Specialized non-standard axis height.
+|-
+|Series20||35mm||14x14mm||6mm||Specialized non-standard axis height.
 |-
-|Small||2"||Intended for lenses up to 1" high, including salvaged projector, disposable camera, and microscope components.
+|Series40||30.8mm||18x28mm||6mm||
 |-
-|Large||8"||Accommodates larger lenses, particularly for light gathering and projection systems.
+|Series60||30.8mm||28x38mm||2mm||
 |-
-|ExtraLarge||13"||Accommodates modest Fresnel lenses.
 |}
-====Optical Rail Axis Heights====
+====Mounting Holes====
+Tolerances intended for well-calibrated 3D printers.
+=====Table=====
+* Screw diameter - 6mm (M6) to 6.35mm (¼in UNC) .
+* Hole spacing - 25mm (metric) to 25.4mm (1in imperial) .
+* Hole size - 8mm .
+* Hole spacing - 25.2 mm .
+=====Extrusion=====
+* Screw diameter - 5mm (M5) .
+* Hole spacing - 20mm .
+* Hole size - 5.5mm .
+* Hole spacing - 20.25mm .
+====Optical Table Axis Heights====
+Standard axis heights are based upon typical hardware for 1" grid optical tables. Mounts for other arrangements, such as a 20series extrusions, should use corespondingly lower heights. Options to mount such hardware to a standard table through intermediate stages, such as 20series extrusions themselves, should be preserved.
+Small axis height is typical, and should be assumed unless noted otherwise.
 {| border="1" style="border-collapse:collapse"
 !Element Size
-!Height
+!TableHeight
+!ExtrusionHeight
+!Comments
+|-
+|Small||2in/50.8mm||30.8mm||Intended for lenses up to 1" high, including salvaged projector, disposable camera, and microscope components.
 |-
-|Small||1.15"
+|Large||8in/203.2mm||183.2mm||Accommodates larger lenses, particularly for light gathering and projection systems.
 |-
-|Large||6.25"
+|ExtraLarge||13in/330.2mm||310.2mm||Accommodates modest Fresnel lenses.
 |-
 |}
@@ Line 83: / Line 120: @@
 * Lens Mount - http://www.thingiverse.com/thing:26752/#files http://www.thingiverse.com/thing:62693/#files
 * OpenSource Optics - http://www.appropedia.org/Open_source_optics
+* Linear Translator - http://www.thingiverse.com/thing:144838
+* Metal Lens Mounts - http://www.edmundoptics.com/optomechanics/optical-mounts-plates/lens-mounts/
+* Lasercut Optics Bench - https://hackaday.io/project/10707-lasercut-optics-bench

OpticalSubsystems: Difference between revisions

From HacDC Wiki