Photolithography Supplies: Difference between revisions
From HacDC Wiki
(Created page with "=Premanufactured= =Raw= ==Substrate== * [http://www.goldmine-elec-products.com/prodinfo.asp?number=G17455 5 x 8 Scissor Cut Ultra Thin Copper Clad - Cheap for Photolithograph...") |
|||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Category:PA_SUPPLIES]] | |||
[[Category:Photolithography PCB Fab]] | |||
=Premanufactured= | =Premanufactured= | ||
These materials work well... | |||
==Substrate== | |||
* [http://www.mouser.com/Tools-Supplies/Prototyping-Products/Copper-Clad-Boards/_/N-b11ou?P=1yzsoajZ1yzvq68 Variety of presensitized copper clad board from mouser.] [http://www.alliedelec.com/images/products/datasheets/bm/MG_CHEMICALS/70125847.pdf Datasheet.] Specifically recommend 590-660 . | |||
==Developer Chemicals== | |||
* [http://www.mouser.com/ProductDetail/MG-Chemicals/418-500ML/?qs=X5SXQx2ktnP2R5Pl77QFKw%3d%3d Positive Developer Chemical - Compatible with above presensitized copper clad board.] | |||
=Raw= | =Raw= | ||
Starting from raw materials may be cheaper and doable, but has yet to be thoroughly tested. | |||
==Substrate== | ==Substrate== | ||
* [http://www.goldmine-elec-products.com/prodinfo.asp?number=G17455 5 x 8 Scissor Cut Ultra Thin Copper Clad - Cheap for Photolithographic PCB Fab] | * [http://www.goldmine-elec-products.com/prodinfo.asp?number=G17455 5 x 8 Scissor Cut Ultra Thin Copper Clad - Cheap for Photolithographic PCB Fab] | ||
| Line 8: | Line 18: | ||
==Developer Chemicals== | ==Developer Chemicals== | ||
* [http://www.amazon.com/Church-03020-Arm-Hammer-Washing/dp/B0029XNTEU/ref=sr_1_1?ie=UTF8&qid=1387395481&sr=8-1&keywords=washing+soda Sodium Carbonate Washing Soda. May not be suitable for processing positive resists.] | * [http://www.amazon.com/Church-03020-Arm-Hammer-Washing/dp/B0029XNTEU/ref=sr_1_1?ie=UTF8&qid=1387395481&sr=8-1&keywords=washing+soda Sodium Carbonate Washing Soda. May not be suitable for processing positive resists.] | ||
Positive developer chemicals apparently use a Sodium Hydroxide and Sodium Silicate mixture. This may reliably permit deep development without overdependent of unexposed regions. | |||
Latest revision as of 00:02, 8 April 2014
Premanufactured
These materials work well...
Substrate
- Variety of presensitized copper clad board from mouser. Datasheet. Specifically recommend 590-660 .
Developer Chemicals
Raw
Starting from raw materials may be cheaper and doable, but has yet to be thoroughly tested.
Substrate
- 5 x 8 Scissor Cut Ultra Thin Copper Clad - Cheap for Photolithographic PCB Fab
- 10x 6x8" Photosensitive Dry Film Sheets
Developer Chemicals
Positive developer chemicals apparently use a Sodium Hydroxide and Sodium Silicate mixture. This may reliably permit deep development without overdependent of unexposed regions.
This category currently contains no pages or media.