CNC Mill Log: Difference between revisions
From HacDC Wiki
(Created page with "When something goes wrong, its nice to note it here. *Milling platform is no longer level, thanks to the screws holding it down being loosened up. Needs resurfacing. 04/11/12") |
No edit summary |
||
| (8 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
When something goes wrong, its nice to note it here. | [[Category:CNC_Mill]] | ||
When something goes wrong, its nice to note it here. Also nice to note any fixes (eg. resurfacing the milling platform). | |||
*Milling platform is no longer level, thanks to the screws holding it down being loosened up. Needs resurfacing. | == 2 May. 2013 == | ||
Maximum X-Axis feed rate of 60in/min was moderately error prone, occasionally triggering emergency stop. Reduced to 40in/min, identical to Y-Axis setting. | |||
[[User:mirage335|mirage335 2013-05-02]] | |||
== 2 Feb. 2013 == | |||
Settings on Mach3 were incorrect; communication with the mill controller was impossible. The following settings changes were made (and some fiddling done) and the mill appears to be functioning and calibrated well: | |||
*Changing the port to address 0x378 allowed the spindle control to function. | |||
*Changing X,Y,Z,A drive and step ports to port 1 (0x378) and setting low trigger on axis X. | |||
*Recalibrated "steps per" with the calibration wizard under ''settings'' using dial indicator (now set for ~16250). | |||
Note: Often restarting Mach3 seems to be required to actually update some of the port settings (although it pretends otherwise). Mill calibration was accurate to only ~0.003" (which maybe a limit imposed by the limited rigidity of the mill+stand). | |||
[[User:Nock|Shawn Nock (OpenPGP: 0x65118FA5)]] 12:47, 3 February 2013 (PST) | |||
== 22 Jan. 2013 == | |||
*Major upgrades in progress thanks to TJ. | |||
== 10 July 2012 == | |||
*Platform still needs replacing, but Barlow resurfaced the remaining usable area. At least now it is level again. | |||
== 28 Apr. 2012 == | |||
*Someone accidentally resurfaced the milling platform (milled too deep). Now the platform needs replacing. | |||
== 11 Apr. 2012 == | |||
*Milling platform is no longer level, thanks to the screws holding it down being loosened up. Needs resurfacing. | |||
Latest revision as of 20:14, 2 May 2013
When something goes wrong, its nice to note it here. Also nice to note any fixes (eg. resurfacing the milling platform).
2 May. 2013
Maximum X-Axis feed rate of 60in/min was moderately error prone, occasionally triggering emergency stop. Reduced to 40in/min, identical to Y-Axis setting. mirage335 2013-05-02
2 Feb. 2013
Settings on Mach3 were incorrect; communication with the mill controller was impossible. The following settings changes were made (and some fiddling done) and the mill appears to be functioning and calibrated well:
- Changing the port to address 0x378 allowed the spindle control to function.
- Changing X,Y,Z,A drive and step ports to port 1 (0x378) and setting low trigger on axis X.
- Recalibrated "steps per" with the calibration wizard under settings using dial indicator (now set for ~16250).
Note: Often restarting Mach3 seems to be required to actually update some of the port settings (although it pretends otherwise). Mill calibration was accurate to only ~0.003" (which maybe a limit imposed by the limited rigidity of the mill+stand).
Shawn Nock (OpenPGP: 0x65118FA5) 12:47, 3 February 2013 (PST)
22 Jan. 2013
- Major upgrades in progress thanks to TJ.
10 July 2012
- Platform still needs replacing, but Barlow resurfaced the remaining usable area. At least now it is level again.
28 Apr. 2012
- Someone accidentally resurfaced the milling platform (milled too deep). Now the platform needs replacing.
11 Apr. 2012
- Milling platform is no longer level, thanks to the screws holding it down being loosened up. Needs resurfacing.