Machine Shop Classes: Difference between revisions
From HacDC Wiki
No edit summary |
No edit summary |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
This page is for the machine shop classes for the space. Currently basic lathe classes are being taught, but this may expand to include other classes/tools as they become available. (This page is a work in progress, please contribute!) | This page is for the machine shop classes for the space. Currently basic lathe classes are being taught, but this may expand to include other classes/tools as they become available. (This page is a work in progress, please contribute!) | ||
| Line 19: | Line 17: | ||
[http://www.sciplus.com/search.cfm/scategory/TAM/term/calipers/srch.fp/1 American Science and Surplus $20 Digital Calipers] | [http://www.sciplus.com/search.cfm/scategory/TAM/term/calipers/srch.fp/1 American Science and Surplus $20 Digital Calipers] | ||
| Line 28: | Line 27: | ||
*When boring and turning, it's much easier to stand at the END of the machine (so you're looking down the axis of the part) than to stand "in front" where you'd normally think to. (Tom C. 10/13/10) | *When boring and turning, it's much easier to stand at the END of the machine (so you're looking down the axis of the part) than to stand "in front" where you'd normally think to. (Tom C. 10/13/10) | ||
*Don't be afraid to use both hands on the dials. They're small, but two hands will give better control and smoother finishes. (Tom C. 10/13/10) | *Don't be afraid to use both hands on the dials. They're small, but two hands will give better control and smoother finishes. (Tom C. 10/13/10) | ||
==Suggestions== | ==Suggestions== | ||
| Line 52: | Line 53: | ||
**Polishing | **Polishing | ||
*Threading (may take some time, I (Tom) will need to teach myself first) | *Threading (may take some time, I (Tom) will need to teach myself first) | ||
==Successful Parts!== | ==Successful Parts!== | ||
Feel free to post up proof of your awesome part-making skills here. Stories and photos encouraged. | Feel free to post up proof of your awesome part-making skills here. Stories and photos encouraged. | ||
I lathed up some couplers for my reprap Z axis rods. Somewhat crude in that I used rectangular stock, but it is a vast improvement over the plastic part that had failed. Piece is aluminium, and was drilled through at 5mm and then drilled half way through at 8mm. I followed up by cross drilling at 3mm and tapping for 4mm screws to secure the shafts in the coupler. -John | |||
[http://lh6.ggpht.com/_UvQljTfsdFU/TS039Pz8QAI/AAAAAAAAA2s/GikRllVOCeE/s800/CIMG7202.JPG Lathed motor to threaded rod connector] | |||
I hobbed a bolt for use in a reprap Wade's extruder. The bolt was a 5/16 x 2.5" hex head bolt that was to be used in the extruder. The bolt was notched, then an m3 tap was put in the headstock and the bolt was hobbed to have teeth to move the filament. A hobbing jig is in the reprap bin for future use in case anyone else needs to create this part. The whole procedure took less than 10 minutes. -John | |||
[[Category:Classes]] | |||
Latest revision as of 04:24, 4 April 2012
This page is for the machine shop classes for the space. Currently basic lathe classes are being taught, but this may expand to include other classes/tools as they become available. (This page is a work in progress, please contribute!)
Resources
Further Reading
Material Sources
American Science and Surplus $20 Digital Calipers
Lessons Learned
List of tips gleaned from our own mistakes experiences. Please contribute (with attribution / date).
- The speed settings from the classes are suggestions only. When in doubt, sacrifice a small test piece to fiddle with speeds (both motor speed and hand speed) and find the optimal settings. (Tom C. 10/13/10)
- When boring and turning, it's much easier to stand at the END of the machine (so you're looking down the axis of the part) than to stand "in front" where you'd normally think to. (Tom C. 10/13/10)
- Don't be afraid to use both hands on the dials. They're small, but two hands will give better control and smoother finishes. (Tom C. 10/13/10)
Suggestions
Suggested additions to our tool selection, classes, projects, etc.
Operations to Learn
- Knurling
- Tapered cutting
Tools to Buy
- Knurling Tool
See also Wiki Procurement Page
Class Projects
- DIY Flashlight (VERY advanced, we may need to work up to this)
- Control Knobs (Possibly pair with an electronics class?)
- Aesthetics and Finishes (mini-class) - we make a handful of decorative rings with different tools, they make great gifts!
- Knurling
- Straight and angled grooving
- Polishing
- Threading (may take some time, I (Tom) will need to teach myself first)
Successful Parts!
Feel free to post up proof of your awesome part-making skills here. Stories and photos encouraged.
I lathed up some couplers for my reprap Z axis rods. Somewhat crude in that I used rectangular stock, but it is a vast improvement over the plastic part that had failed. Piece is aluminium, and was drilled through at 5mm and then drilled half way through at 8mm. I followed up by cross drilling at 3mm and tapping for 4mm screws to secure the shafts in the coupler. -John Lathed motor to threaded rod connector
I hobbed a bolt for use in a reprap Wade's extruder. The bolt was a 5/16 x 2.5" hex head bolt that was to be used in the extruder. The bolt was notched, then an m3 tap was put in the headstock and the bolt was hobbed to have teeth to move the filament. A hobbing jig is in the reprap bin for future use in case anyone else needs to create this part. The whole procedure took less than 10 minutes. -John