Actions

Prusa Mendel Documentation: Difference between revisions

From HacDC Wiki

Line 44: Line 44:
| 4 || ballpoint pen springs || Spring || Space
| 4 || ballpoint pen springs || Spring || Space
|-
|-
| 6 || M8×370mm || Threaded rod || 3 per side - (Mark) / (Pete) / (Space)
| 6 || M8×370mm || Threaded rod || 3 per side - (Mark) / (Space)
|-
|-
| 4 || M8×294mm || Threaded rod || front / rear - (Mark) / (Pete) / (Space)
| 4 || M8×294mm || Threaded rod || front / rear - (Mark) / 2 x 600 Pete / (Space)
|-
|-
| 3 || M8×440mm || Threaded rod || top / bottom - (Mark) / (Pete) / (Space)
| 3 || M8×440mm || Threaded rod || top / bottom - (Mark) / Pete / (Space)
|-
|-
| 2 || M8×210mm || Threaded rod || Z-leadscrew - (Mark) / (Pete) / (Space)
| 2 || M8×210mm || Threaded rod || Z-leadscrew - (Mark) / 1 x Pete / (Space)
|-
|-
| 1 || M8×50mm || Threaded rod || or bolt for X idler - (John) / (Mark) / (Pete) / (Space)
| 1 || M8×50mm || Threaded rod || or bolt for X idler - (John) / (Mark) / Pete / (Space)
|-
|-
| 2 || 8mm×420mm || Smooth rod || X-bar - (Pete) / (Space)
| 2 || 8mm×420mm || Smooth rod || X-bar - Pete / (Space)
|-
|-
| 2 || 8mm×406mm || Smooth rod || Y-bar - (Pete) / (Space)
| 2 || 8mm×406mm || Smooth rod || Y-bar - Pete / (Space)
|-
|-
| 2 || 8mm×350mm || Smooth rod || Z-bar - (Pete) / (Space)
| 2 || 8mm×350mm || Smooth rod || Z-bar - Pete / (Space)
|-
|-
| 1 || 225mm×225mm print top plate || Thick Sheet || (space)
| 1 || 225mm×225mm print top plate || Thick Sheet || (space)

Revision as of 14:12, 23 May 2011

A new reprap printer will built along the lines of the Prusa Mendel. You can find details of the Prusa design at the Prusa Mendel page on the reprap wiki, or you can view the sources for the Prusa at github

Intro

Having another 3d printer in the space will allow us to always have a working machine and to use one machine to help fix another if there are problems. It will also enable several people to print things out at the same time. The goal is to document this build so others can make their own printer following our documentation.

Materials for the build

BOM for Prusa Mendel

Non-Printed Parts ("vitamins")

Quantity Description Type Comments
83 M8 nut Fastener (John)
93 M8 washer Fastener (John)
6 M8×30 mudguard / fender washers Fastener (John)
2 M4×20 bolt Fastener (John)
2 M4 nut Fastener (John)
2 M4 washer Fastener (John)
22 M3×10 bolt Fastener (John) / Space
8 M3×20 bolt Fastener (John) / Space
8 M3×25 bolt Fastener (John) / Space
4 M3×40 bolt Fastener (John) / Space
70 M3 washer Fastener (John) / Space
40 M3 nut Fastener (John) / Space
2 M3 grub screw / set screw Fastener (John) / (Pete)
3 608 roller skate / inline skate / skateboard bearing Bearings (Space) / Pete
4 ballpoint pen springs Spring Space
6 M8×370mm Threaded rod 3 per side - (Mark) / (Space)
4 M8×294mm Threaded rod front / rear - (Mark) / 2 x 600 Pete / (Space)
3 M8×440mm Threaded rod top / bottom - (Mark) / Pete / (Space)
2 M8×210mm Threaded rod Z-leadscrew - (Mark) / 1 x Pete / (Space)
1 M8×50mm Threaded rod or bolt for X idler - (John) / (Mark) / Pete / (Space)
2 8mm×420mm Smooth rod X-bar - Pete / (Space)
2 8mm×406mm Smooth rod Y-bar - Pete / (Space)
2 8mm×350mm Smooth rod Z-bar - Pete / (Space)
1 225mm×225mm print top plate Thick Sheet (space)
1 140mm×225mm print bottom plate Thick Sheet space
1 840mm×5mm T5 pitch timing belt Belt T2.5 from Pete if it's useful
1 1380mm×5mm T5 pitch timing belt Belt T2.5 from Pete if it's useful
5 NEMA 17 bipolar stepper motor Stepper John
50 small cable binder / ziptie Misc (space)
1 Wade's Geared Extruder ZAC
1 Electronics + endstops gen3 from John or Tiny G from Alden

John

1x gen3 mobo 2x gen3 EC 5x steppers 4x stepper controllers (we'll have to pull these from the cupcake and have the cupcake use the mbi ones) 1x p4ac 4 axis stepper controller carrier board (we'll have to pull this from the cupcake too) 1x wade's extruder (assembled and working) 1x 36mm brass barrel 1x 0.5mm mbi nozzle 1x 0.5mm makergear bighead nozzle Insulator materials (have to make and document on lathe) nuts/bolts/washers - I have tons plywood/mdf for build platform

Xaq

RP parts

Still needed

threaded rods smooth rods heated build platform (if we want it, can get away with some other hacks if we want, or leave it out altogether)

Offers

Mark has threaded rod Alden has a Tiny G board... this is attractive Pete smooth rod