Makerbot Operators Log: Difference between revisions
From HacDC Wiki
Hexagon5un (talk | contribs) No edit summary |
Hexagon5un (talk | contribs) No edit summary |
||
| Line 3: | Line 3: | ||
* Nov 27, 2010. (Elliot.) Printed small odds and ends, just to watch it go. Looks great. The new spool which Dan B and I built seems to work fine, and certainly won't tangle. I've been working on raftless settings, and it's looking great. Will post up my settings in a bit. Printed a few of the heater-retainer collars for later in case we need them, and tossed them in the reprap box. | * Nov 27, 2010. (Elliot.) Printed small odds and ends, just to watch it go. Looks great. The new spool which Dan B and I built seems to work fine, and certainly won't tangle. I've been working on raftless settings, and it's looking great. Will post up my settings in a bit. Printed a few of the heater-retainer collars for later in case we need them, and tossed them in the reprap box. | ||
* Nov 26, 2010. (Elliot.) Having broken the hot end of the extruder, I needed to fix it. Took it completely apart and soaked all the parts in acetone, getting all the melted plastic off. I reinstalled things as per the makerbot instructions, with the exception of using teflon tape to (electrically) insulate the barrel from the nichrome wire, because its original sheathing had come off during removal. Noticed that the brass barrel was installed upside-down, so I fixed that. The nozzle seems to be flowing a lot now -- so much that I had to reconfigure skeinforge to deal with the extra plastic. We'll see if it holds up. | * Nov 26, 2010. (Elliot.) Having broken the hot end of the extruder, I needed to fix it. Took it completely apart and soaked all the parts in acetone, getting all the melted plastic off. I reinstalled things as per the makerbot instructions, with the exception of using teflon tape to (electrically) insulate the barrel from the nichrome wire, because its original sheathing had come off during removal. Noticed that the brass barrel was installed upside-down, so I fixed that. The nozzle seems to be flowing a lot now -- so much that I had to reconfigure skeinforge to deal with the extra plastic. We'll see if it holds up. Printed out a [http://www.thingiverse.com/thing:4036 brutstruder] and the plastic axles for the new feed spool. | ||
Printed out a [http://www.thingiverse.com/thing:4036 brutstruder] and the plastic axles for the new feed spool. | |||
* Nov 24, 2010. (Elliot and Will G.) Still having problems with intermittent extruder stoppage. Will and Elliot removed the hot end and cleaned it out. That wasn't the problem. Elliot noticed that the idler wheel was binding, fixed that. Still not the problem, though it has sufficient strength to push through whatever is giving the high back-pressure. Elliot started to re-do the hot end again, and probably messed up the heater in the process. Hopefully it's just a loose wire, but the insulation and heating element may need to be re-worked. Sucks.... | * Nov 24, 2010. (Elliot and Will G.) Still having problems with intermittent extruder stoppage. Will and Elliot removed the hot end and cleaned it out. That wasn't the problem. Elliot noticed that the idler wheel was binding, fixed that. Still not the problem, though it has sufficient strength to push through whatever is giving the high back-pressure. Elliot started to re-do the hot end again, and probably messed up the heater in the process. Hopefully it's just a loose wire, but the insulation and heating element may need to be re-worked. Sucks.... | ||
Revision as of 20:07, 28 November 2010
When you use the Cupcake, please add notes here. Newest at top.
- Nov 27, 2010. (Elliot.) Printed small odds and ends, just to watch it go. Looks great. The new spool which Dan B and I built seems to work fine, and certainly won't tangle. I've been working on raftless settings, and it's looking great. Will post up my settings in a bit. Printed a few of the heater-retainer collars for later in case we need them, and tossed them in the reprap box.
- Nov 26, 2010. (Elliot.) Having broken the hot end of the extruder, I needed to fix it. Took it completely apart and soaked all the parts in acetone, getting all the melted plastic off. I reinstalled things as per the makerbot instructions, with the exception of using teflon tape to (electrically) insulate the barrel from the nichrome wire, because its original sheathing had come off during removal. Noticed that the brass barrel was installed upside-down, so I fixed that. The nozzle seems to be flowing a lot now -- so much that I had to reconfigure skeinforge to deal with the extra plastic. We'll see if it holds up. Printed out a brutstruder and the plastic axles for the new feed spool.
- Nov 24, 2010. (Elliot and Will G.) Still having problems with intermittent extruder stoppage. Will and Elliot removed the hot end and cleaned it out. That wasn't the problem. Elliot noticed that the idler wheel was binding, fixed that. Still not the problem, though it has sufficient strength to push through whatever is giving the high back-pressure. Elliot started to re-do the hot end again, and probably messed up the heater in the process. Hopefully it's just a loose wire, but the insulation and heating element may need to be re-worked. Sucks....
Makerbot is in a non-working state ATM.
- Nov 20, 2010. (Elliot and Tommy) Noticed that gear motor was out of line. Tommy and I added a bearing to it. Extruder still just randomly stops extruding after 15 minutes or so.
- Nov 18, 2010. (Elliot) Printed out some widgets. Extruder head stopped extruding halfway through a print, turned out to be due to ABS bits fouling up the pushing-gear teeth. Also had some troubles with adhesion of the raft to platform.