Actions

Robot Project 2021 Notes: Difference between revisions

From HacDC Wiki

No edit summary
No edit summary
Line 65: Line 65:
* 10-year-olds my ass. This required a hell of a lot of strength to snap the chassis together without snapping.
* 10-year-olds my ass. This required a hell of a lot of strength to snap the chassis together without snapping.
* Don’t forget: there are '''eight''' snap points: Four at the corners and two above the wheels. I got the outer four, and didn’t notice the wheel ones until after the fact. It took forever to get those to snap into place.
* Don’t forget: there are '''eight''' snap points: Four at the corners and two above the wheels. I got the outer four, and didn’t notice the wheel ones until after the fact. It took forever to get those to snap into place.
-----
== Wiring ==
* Motor wires ''may'' need to be flipped (black to red and vice versa).
* '''IMPORTANT SAFETY TIP''': The instructions fail to mention that the battery pack should be rotated 90 degrees after slipping in the back so that the power cable is coming out the left side behind the wheel – or if the instructions did mention it, that tidbit wasn’t clear to me.
* God help you if you ever have to replace the batteries…
-----
== Powering on ==
* Providing power causes the <code>micro:bit</code> to boot with an introductory “H…E…L…L…O” and then prompts you to push buttons A and then B.


-----
-----

Revision as of 14:12, 9 February 2021

Sparkfun Red Hat Co.Lab Robot

(BBC micro:bit + Sparkfun moto:bit)

Sparkfun moto:bit Carrier Board

The moto:bit - micro:bit Carrier Board (Qwiic) uses a Qwiic interface? and offers pins for:

  • six 3-pin sensors,
  • two 3-pin servo motors
  • two 2-pin “big” motors

and an I2C bus (as well as a Qwiic “port” and power switch)

       +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
                              micro:bit CONNECTOR BUS


           ANALOG           DIGITAL
           DIGITAL            ONLY
              |                |
       +-+----+-------+ +------+------+-+
       | |            | |             | |                           SCL  ☐
    P0 • •  P1     P2 • • P8      P12 • • P14      P15 • • P16      SDA  ☐
   3V3 • • 3V3    3V3 • • 3V3     3V3 • • 3V3      VCC • • VCC      3V3  ☐
   GND • • GND    GND • • GND     GND • • GND      GND • • GND      GND  ☐

      SENSOR         SENSOR          SENSOR           SERVO         I2C BUS



        BLACK •   LEFT                           RIGHT  • RED
        RED   •   MOTOR                          MOTOR  • BLACK


   POWER IN
  INPUT RANGE
  VCC: 3 - 11V                                                  QWIIC


                  STOP                RUN
                 MOTORS              MOTORS

Wheel Motor Assembly

  • Geez! They weren’t kidding! Getting the front motor mounts over the big motors was a PITA! Ultimately, brute forcing it with my hand rather than pliers proved the most successful.
  • The rear motor mounts were only slightly better.
  • Mounting the assemblage to the bottom chassis, I was sure I was going to snap something in two or tear out a wire.
  • The motor I’ve mounted on the right side has a black wire whose solder point looks suspect…

Line folowing sensors

  • The pins should be sticking out on the smooth side of the “bottom” mount.
  • By contrast, this slipped together so easily that I worry it might be too loose, though it will undoubtedly tighten up when mounted to the chassis.
  • This tutorial seems to be a thinly disguised advertisment for electrical tape…

Chassis

  • 10-year-olds my ass. This required a hell of a lot of strength to snap the chassis together without snapping.
  • Don’t forget: there are eight snap points: Four at the corners and two above the wheels. I got the outer four, and didn’t notice the wheel ones until after the fact. It took forever to get those to snap into place.

Wiring

  • Motor wires may need to be flipped (black to red and vice versa).
  • IMPORTANT SAFETY TIP: The instructions fail to mention that the battery pack should be rotated 90 degrees after slipping in the back so that the power cable is coming out the left side behind the wheel – or if the instructions did mention it, that tidbit wasn’t clear to me.
  • God help you if you ever have to replace the batteries…

Powering on

  • Providing power causes the micro:bit to boot with an introductory “H…E…L…L…O” and then prompts you to push buttons A and then B.