|
|
| (3 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| {{Floating TOC}}
| | Obsolete. |
| [[Category:Occupancy_Sensor]]
| |
| | |
| =Status=
| |
| WRT54GL based occupancy sensor currently providing valid data.
| |
| NetPLC has been tested, ready for installation.
| |
| | |
| =Maintenance=
| |
| | |
| ==NetPLC==
| |
| ===Repositories===
| |
| https://github.com/mirage335/NetPLC
| |
| https://github.com/HacDC/NetPLC-HacDC-Firmware
| |
| | |
| ===Workstation===
| |
| The WYSE terminal labeled "NetPLC-Workstation" has been provided a bootable Knoppix USB stick with [https://github.com/HacDC/NetPLC-HacDC-Firmware/blob/master/NetPLC_Term.sh a simple serial-terminal interactive shell script]. With the workstation turned on, and NetPLC hardware connected by USB, type "NetPLC_Term.sh" to begin.
| |
| | |
| ===CLI===
| |
| Configuration is by command-line interface (CLI). Type "commands" for the built-in reference, or [https://github.com/HacDC/NetPLC-HacDC-Firmware/blob/master/src/CLI/CLI.ino check the source]. Parameters are tab separated by tabs only.
| |
| | |
| ===Reference===
| |
| Some of the fimware-included commands are as follows.
| |
| <nowiki>
| |
| commands
| |
| shownet
| |
| readout
| |
| recentTag
| |
| formatMembers
| |
| countMembers
| |
| showMembers
| |
| addMember <shortName> <tagID> <1/0>
| |
| delMember <recno>
| |
| enableMember <recno>
| |
| disableMember <recno>
| |
| closeSpace
| |
| openSpace
| |
| </nowiki>
| |
| | |
| Note the database is limited to short names and about 50 members, at ~500B EEPROM storage.
| |
| | |
| =Planned Upgrades=
| |
| *) SD card support is easy to provide to AVR/Arduino platforms, offering virtually unlimited storage capacity.
| |
| *) RN171 (WiFi) should be moved to software serial port, completely freeing the hardware UART for external peripherials.
| |
| *) An ATmega2560, rather than ATMega32U4, would offer enough flash space to include telnet-style networked CLI functionality alongside existing requirements.
| |
| | |
| =History=
| |
| HacDC's occupancy sensor has been an evolving project, with several generations of hardware and software contributed by many members. In addition to the hardware designs listed below, members like "haxwithaxe" and "eryc" have contributed supporting infrastructure like [[WOPR]].
| |
| | |
| ==NetPLC==
| |
| Open-source hardware designed by mirage335. Both RFID and Occupancy Sensing functions are supported. Compatible with Arduino Leonardo bootloader, based on an ATMega32U4 microcontroller, with on-board provisions for wired and wireless connectivity.
| |
| | |
| ==WRT54GL==
| |
| Second occupancy sensor, configured by mirage335, using a WRT54GL with barebones AVR chip hardwired to internal serial TX/RX pads. Data was relayed directly to internet resources (eg. front page icon) by the router over wired and/or wireless connectivity as available.
| |
| | |
| ==Arduino==
| |
| First occupancy sensor was configured by Martin, consisting of an Arduino, a Radioshack photoresistor (276-1657) and a Quest passive infrared motion detector. Data was retrieved by a desktop computer via USB, then published to internet resources (eg. Google Calendar).
| |
| | |
| =Credits=
| |
| Martin Rothfield
| |
| haxwithaxe
| |
| eryc
| |
| Many More
| |
